Yukon Gear & Axle Re-Gear Kit, Dana 30 (M186) Front and Dana 44 (M220) Rear, 4.56 Ratio, Jeep Wrangler JL Non-Rubicon
SKU: yukYGK078
Overview
Yukon Gear Kits combine all the parts needed for a re-gear project in one single part number: front and rear ring & pinion gear sets plus the proper Yukon Master Overhaul Kits. The kits contain the gears, bearings, and all the small parts needed to fully rebuild the differentials.
Key Features
- Front and rear ring & pinion gear sets in one part number
- Front and rear Yukon Master Overhaul Kits included
- Gears, bearings, and all the small parts needed to fully rebuild both differentials
- High-grade steel gears with fitment designed to OEM specifications
What's Included
- Front ring & pinion gear set
- Rear ring & pinion gear set
- Front Master Overhaul Kit
- Rear Master Overhaul Kit
Specifications
| Front axle | Dana 30 (M186) |
| Rear axle | Dana 44 (M220) |
| Gear ratio | 4.56 |
| UPC | 883584310785 |
| Shipping box | 16 x 20 x 14 in, 68.50 lb |
Installation
Professional installation is recommended. Gear setup means setting pinion depth, pinion bearing preload, backlash, and carrier preload, then verifying the contact pattern with gear-marking compound, using tools most home garages do not have, including a dial indicator, bearing press and pullers, and inch-pound and foot-pound torque wrenches. Quadratec rates this job Level 3 (Advanced), with an installation time of about 4 to 6 hours for both axles.
Yukon's break-in procedure is a condition of the gear warranty, not a suggestion. Drive lightly for the first 15 to 20 miles, then stop and let the differential cool before continuing. Avoid heavy acceleration for the first 100 miles. Drive at least 500 miles before towing. The first time you tow, go less than 15 miles with the full load, stop and let the differential cool about 20 minutes, and repeat that twice more, for 45 miles total. Change the gear oil after the first 500 miles to remove metal particles and the phosphoric coating shed during break-in. Overheating or overloading new gears breaks down the gear oil and destroys the ring and pinion, and Yukon states that this can be determined by inspection and will void the gears' warranty.
Before teardown, check all bearings and small parts against the parts invoice. Yukon's own installation manual starts disassembly with verifying that all new parts match the application and the invoice.
Fitment
Fits Jeep Wrangler JL Non-Rubicon models with the Dana 30 (M186) front and Dana 44 (M220) rear axle combination.
Axle identification is the number-one fitment risk on these Jeeps. Dana 30 is the M186 (non-Rubicon front), Dana 35 is the M200 (non-Rubicon rear), Dana 44 front is the M210, and Dana 44 rear is the M220. Order by axle, not by trim badge alone.
Carrier note: Yukon's tech line states that new carriers are not required for the gear swap itself on these applications. If you plan to add a locker or limited slip at the same time, the carrier decision changes, because a locker or limited slip replaces the carrier. Confirm your current ratio and carrier with your installer before ordering.
Warranty
Covered by a 1-year warranty against manufacturing defects. Yukon's warranty covers the original retail purchaser and requires installation and maintenance in accordance with Yukon's instructions. At Yukon's discretion, the warranty may be voided if the product is installed on a vehicle with tires that exceed Yukon's maximum recommended tire size. Yukon also offers the Y.E.S. Plan, an optional, separately purchased extended service plan that upgrades a gear set to lifetime, no-questions-asked protection for as long as the original purchaser owns the vehicle. The Y.E.S. Plan is not included with this product; it must be purchased separately and registered within 30 days of purchase.
FAQs
Q: Which ratio should I choose for my tire size?
For the 3.6L V6 with the 8-speed automatic, the widely published guidance is 4.56 for 35-inch tires and 4.88 for 37-inch tires, with 5.13 favored on Gladiators that tow or plan to go bigger. Yukon's own tech line recommends 4.88 for a manual-transmission JL on 35s. This 4.56 ratio is the published match for 35-inch tires on the 3.6L automatic.
Q: What did my Jeep come with stock?
Non-Rubicon JL models came with 3.45 gears, some optioned with 3.73. Rubicon JL, and Rubicon and Mojave JT, came with 4.10. A non-Rubicon JL runs a Dana 30 (M186) front axle with either a Dana 35 (M200) rear or, with the tow package or limited-slip option, a Dana 44 (M220) rear. Rubicon models and all Gladiators run a Dana 44 front (M210) and rear (M220). Confirm your axle and ratio from your build sheet before ordering.
Q: Do front and rear ratios have to match?
Yes. Both axles must run the same ratio, which is why Yukon pairs a front and rear set in its gear packages. Order the ratio you run at the other end.
Overview
Yukon Gear Kits combine all the parts needed for a re-gear project in one single part number: front and rear ring & pinion gear sets plus the proper Yukon Master Overhaul Kits. The kits contain the gears, bearings, and all the small parts needed to fully rebuild the differentials.
Key Features
- Front and rear ring & pinion gear sets in one part number
- Front and rear Yukon Master Overhaul Kits included
- Gears, bearings, and all the small parts needed to fully rebuild both differentials
- High-grade steel gears with fitment designed to OEM specifications
What's Included
- Front ring & pinion gear set
- Rear ring & pinion gear set
- Front Master Overhaul Kit
- Rear Master Overhaul Kit
Specifications
| Front axle | Dana 30 (M186) |
| Rear axle | Dana 44 (M220) |
| Gear ratio | 4.56 |
| UPC | 883584310785 |
| Shipping box | 16 x 20 x 14 in, 68.50 lb |
Installation
Professional installation is recommended. Gear setup means setting pinion depth, pinion bearing preload, backlash, and carrier preload, then verifying the contact pattern with gear-marking compound, using tools most home garages do not have, including a dial indicator, bearing press and pullers, and inch-pound and foot-pound torque wrenches. Quadratec rates this job Level 3 (Advanced), with an installation time of about 4 to 6 hours for both axles.
Yukon's break-in procedure is a condition of the gear warranty, not a suggestion. Drive lightly for the first 15 to 20 miles, then stop and let the differential cool before continuing. Avoid heavy acceleration for the first 100 miles. Drive at least 500 miles before towing. The first time you tow, go less than 15 miles with the full load, stop and let the differential cool about 20 minutes, and repeat that twice more, for 45 miles total. Change the gear oil after the first 500 miles to remove metal particles and the phosphoric coating shed during break-in. Overheating or overloading new gears breaks down the gear oil and destroys the ring and pinion, and Yukon states that this can be determined by inspection and will void the gears' warranty.
Before teardown, check all bearings and small parts against the parts invoice. Yukon's own installation manual starts disassembly with verifying that all new parts match the application and the invoice.
Fitment
Fits Jeep Wrangler JL Non-Rubicon models with the Dana 30 (M186) front and Dana 44 (M220) rear axle combination.
Axle identification is the number-one fitment risk on these Jeeps. Dana 30 is the M186 (non-Rubicon front), Dana 35 is the M200 (non-Rubicon rear), Dana 44 front is the M210, and Dana 44 rear is the M220. Order by axle, not by trim badge alone.
Carrier note: Yukon's tech line states that new carriers are not required for the gear swap itself on these applications. If you plan to add a locker or limited slip at the same time, the carrier decision changes, because a locker or limited slip replaces the carrier. Confirm your current ratio and carrier with your installer before ordering.
Warranty
Covered by a 1-year warranty against manufacturing defects. Yukon's warranty covers the original retail purchaser and requires installation and maintenance in accordance with Yukon's instructions. At Yukon's discretion, the warranty may be voided if the product is installed on a vehicle with tires that exceed Yukon's maximum recommended tire size. Yukon also offers the Y.E.S. Plan, an optional, separately purchased extended service plan that upgrades a gear set to lifetime, no-questions-asked protection for as long as the original purchaser owns the vehicle. The Y.E.S. Plan is not included with this product; it must be purchased separately and registered within 30 days of purchase.
FAQs
Q: Which ratio should I choose for my tire size?
For the 3.6L V6 with the 8-speed automatic, the widely published guidance is 4.56 for 35-inch tires and 4.88 for 37-inch tires, with 5.13 favored on Gladiators that tow or plan to go bigger. Yukon's own tech line recommends 4.88 for a manual-transmission JL on 35s. This 4.56 ratio is the published match for 35-inch tires on the 3.6L automatic.
Q: What did my Jeep come with stock?
Non-Rubicon JL models came with 3.45 gears, some optioned with 3.73. Rubicon JL, and Rubicon and Mojave JT, came with 4.10. A non-Rubicon JL runs a Dana 30 (M186) front axle with either a Dana 35 (M200) rear or, with the tow package or limited-slip option, a Dana 44 (M220) rear. Rubicon models and all Gladiators run a Dana 44 front (M210) and rear (M220). Confirm your axle and ratio from your build sheet before ordering.
Q: Do front and rear ratios have to match?
Yes. Both axles must run the same ratio, which is why Yukon pairs a front and rear set in its gear packages. Order the ratio you run at the other end.
Reviews unavailable.
Shipping Policy Import Image Racing LLC 3200 Hanson St, Fort Myers, FL 33916 Phone: 941-257-9618 · Hours: Monday–Friday, 8am–11pm ET Import Image Racing LLC operates the following online storefronts: Maverick Division (maverickdivision.com, support@maverickdivision.com), Dirty Offroad (dirty-offroad.com), BlackLine Fab (blacklinefab.com), and FS Warehouse (fswarehouse.com). For order questions, contact the support email listed on the storefront you purchased from, or call the number above. Processing time In-stock items ordered before the shipping warehouse's same-day cutoff (shown live on each product page) ship the same business day; otherwise they ship the next business day. We ship Monday through Friday, excluding US federal holidays. Carriers and transit times We ship primarily…
Read full shipping policy →You may return most new, unused items within 30 days of delivery for a refund. Items must be uninstalled, in original packaging, and in resellable condition with all included hardware and documentation. Restocking Fee Returns may be subject to a restocking fee , deducted from your refund. Returns caused by our error (wrong or defective item shipped) are never charged a restocking fee. Return Shipping Return shipping costs are the buyer's responsibility , unless the return is due to our error. We recommend a trackable shipping method; we are not responsible for returns lost in transit. Non-Returnable Items Special order items — parts ordered specifically for you are final sale Items that have been installed, used, or modified Electrical and electronic components once opened Gift…
Read full returns policy →Dirty Offroad
Related Products

Artec Industries
Artec 1-Ton - APEX Front SD Differential Top Cap 2005+ JL6501, Jeep Wrangler JL and Gladiator JT

Artec Industries
Artec JL APEX Rear Axle Truss JL4502, Jeep Wrangler JL

Artec Industries
Artec 1-Ton - APEX Front Superduty Swap Kit 1999-2004 JL6542, Johnny Joints, Jeep Wrangler JL and Gladiator JT

Yukon Gear & Axle
Yukon Gear & Axle Chromoly Rear Axle Shaft, Dana 44 (M220), 32 Spline, 33.9 in, Right Hand, Jeep Wrangler JL and Gladiator JT Rubicon

Yukon Gear & Axle
Yukon Gear & Axle Chromoly Rear Axle Kit, Dana 35 (M200), 29 Spline, 32.3 in, Jeep Wrangler JL

Yukon Gear & Axle
Yukon Gear & Axle Replacement Standard Open Spider Gear Kit, Dana 30, 27 Spline

Yukon Gear & Axle
Yukon Gear & Axle Pinion Preload Solid Spacer and Shim Kit, Front, Jeep Wrangler JL Dana 30

Yukon Gear & Axle
Yukon Gear & Axle Mighty Seal Pinion Seal, Dana 44 (M220) Rear, Jeep Wrangler JL

Yukon Gear & Axle
Yukon Gear & Axle Re-Gear Kit, Dana 44 (M210) Front and Dana 44 (M220) Rear, 4.88 Ratio, Jeep Wrangler JL and Gladiator JT Rubicon

Yukon Gear & Axle
Yukon Gear & Axle Re-Gear Kit, Dana 44 (M210) Front and Dana 44 (M220) Rear, 4.56 Ratio, Jeep Wrangler JL and Gladiator JT Rubicon
Yukon Gear & Axle Re-Gear Kit, Dana 30 (M186) Front and Dana 44 (M220) Rear, 4.56 Ratio, Jeep Wrangler JL Non-Rubicon
